Pool tables are designed for patios and indoor sports arenas. Pool is a game that most play during their leisure time with family and friends. The tables are able to last as long as 20 years with minimal maintenance when they are made from durable material. The part of the structure that is most vulnerable is the felt. In considering pool table refelting Denver residents should know the steps taken in order to come up with excellent results.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
0 comments:
Enregistrer un commentaire